Xianyang small semi-automatic terminal machine

Xianyang small semi-automatic terminal machine

Fully automatic terminal machine is a more convenient machine, we should also know this, fully automatic mechanical equipment Those with greater help can save a lot of labor and increase the output of the factory. It can also help the factory to temporarily relieve the problem of not being able to find workers. However, we are also using the fully automatic terminal machine when we use it. There will be a problem. Some time-division automatic terminal machines will have relatively loud noises after being used for a period of time. We should all be aware of this! So what are the specific reasons for the formation?

We are a small company and we just bought two automatic terminal machines for a big price. How can I extend the service life of the automatic terminal machines? Anyone know? Hi! In order to have a long service life of the automatic terminal machine, this is closely related to our daily use habits, methods of use and maintenance methods. The following are some methods that can prolong the service life of the terminal machine summarized by the staff of the semi-automatic terminal machine, share them here. For newly bought semi-automatic terminal machines. Novices are required to understand the safe operation specifications of the terminal machine, if they are novices. To prevent the operation of the terminal machine, it is also necessary to pay attention to the safety of the operation. Unnecessary losses due to improper operation caused by novice safety operators.

Generally, it is normal to have fine noise. If it is a loud one, then there are these two problems, a. There is abrasion between certain parts and components of the terminal machine, which leads to increased conflicts; b. The screw of the terminal machine is loose during work, causing the parts to vibrate and become rugged.

Xianyang small semi-automatic terminal machine automatic terminal machine manual operation: <1> Turn the operation switch to the adjustment position ○1 (POWEROFF) and the motor will not run at this time. <2> Insert the open-end wrench into the main shaft from the rear door, and press the manual button ○2 (ADJUST) to attract the solenoid. <3> The open-end wrench rotates clockwise to drive the main shaft to rotate one round, the main machine slide block moves up and down to complete a stroke, and a terminal is crimped. <4> Keep pressing the manual button ○2 to turn it in place continuously, and then remove the open-end wrench.

For such problems, what we have to do is to find a solution. If we want to prevent the terminal machine from being disturbed by noise, we must first choose a reasonable tool and improve its installation accuracy. ; At the same time, we must improve the cutting process of the terminal machine. If it is a slender workpiece, try to choose ninety degrees for cutting. In this way, the noise problem of the terminal machine should be alleviated.

Xianyang small semi-automatic terminal machine

Xianyang small semi-automatic terminal machine is more or less problematic in the use of new electronic large-scale machines. For large-scale electrical appliances such as wire cutting machines, there will be more or less problems. There is a big safety hazard. We have to operate according to the instruction manual. Now I will give you some opinions about the computer thread cutting machine. Trouble shooting of the computer thread cutting machine: there is no power on the switch key, first check whether the switch key is plugged into the power source, and then check whether the machine has bad contact, the host cannot start to check that the switch is turned on, the power source is connected, and the pressure monitor is running when the conveyor belt is running. Whether the roller is shifted, re-determine and replace it again. The above is about the failure phenomenon of the computer wire cutting machine. The specific operation method is in accordance with the paper cutter manual.

The daily maintenance precautions of the automatic terminal machine have been introduced here. You can learn more about it, and we should pay more attention to it when we use it. This is for us There is better assistance. Be careful when using the automatic terminal machine. If you need to buy automatic terminal machines, automatic pipe cutting machines, corrugated pipe cutting machines and other mechanical equipment, you can call Contact us, and we also have punctured terminals, terminal molds, terminal copper strips and other accessories, please contact us if you have any needs

Xianyang small semi-automatic terminal machine

Pressure monitoringPre-job preparation: 1. Check if the machine is stable. 2. Check whether the pedal socket and power socket are plugged in securely. three. Check whether the stepper card die set and the upper die are installed correctly. Four. Adjust the height and precision position of the semi-automatic crimping machine. 5 pcs. The spindle positions the punch at the top dead center (electromagnetic cutting control). 6. Remove the wrench and mold adjustment tool. 7. Turn on the power and depress the pedal. If the operation is normal, the preparatory work is complete. Operation method: 1. Turn the power switch to the "on" position. 2. Place the processed material in the proper position of the semi-automatic terminal connector. three. Step on the pedal once, electromagnetically release the separator, make the upper die press down from the top dead center to the bottom dead center, put the processed material into the terminal joint and combine, then return to the original position.

It is necessary to add butter to the crimping part of the automatic terminal machine every week, and apply it evenly on the surface of the high-speed bearing and around the pressure block

Pressure monitoring to use laser to strip wires is a new application of laser in material processing. From the production process, a wire stripping machine is used. The ultra-fine coaxial cable has fine production technology and high technical content, and its own cable has excellent anti-EMI effects. There are multiple sets of wire processing equipment and testing instruments, and the pressure monitors various wire harnesses of 30K daily. The company produces high-voltage cables for LCD screens. For wire laser machines, we use 24-hour after-sales service nationwide, on-site installation training for equipment, and ultra-fine coaxial cable processing belongs to micro-processing technology. What we provide is not only simple production equipment, but also technical guidance for processing and on-site craftsmanship. teach. The order quantity of ultra-fine coaxial cable (unit) price (excluding freight) g1001.00 yuan/unit becomes the supplier association. Wire limit outer diameter 0.44 (mm) Insulation thickness 0.05 (mm) Product certification 3C can be produced, designed and processed

Xianyang small semi-automatic terminal machine

Xianyang small semi-automatic terminal machine

What we provide is not only simple production equipment pressure monitoring, but also technical guidance for processing and teaching guidance for on-site craftsmanship. Aiming at the current Dongguan ultra-fine coaxial line processing laser semi-automatic wire stripping machine. The laser wire stripping machine uses laser to strip the wire, which is the laser in the material. The processing of ultra-fine coaxial wire laser wire stripping belongs to the micro processing technology. Improve customer output and product qualification rate. The ultra-fine coaxial line laser wire stripping machine, the ultra-fine coaxial line processing technology belongs to the micro-processing technology,